速率模式飞轮姿态控制系统飞轮组合平稳切换方法

对速率模式飞轮姿态控制系统的能控性、稳定性和飞轮组合切换过程进行了研究，揭示了在飞轮组合切换过程中引起卫星姿态抖动的原因，提出了通过对残余角动量进行卸载并将卸载函数同时前馈到系统输入的方法，以保持卫星姿态的稳定度。从理论上证明了可引入残余角动量进行卸载，将卸载函数同时前馈到系统输入，并且不改变原系统的能控性和稳定性。给出了某卫星飞轮切换应用实例，说明了飞轮组合平稳切换方法的有效性。     

Simulation and Analysis of Electromagnetic Force in Laser Melting Deposition by Electromagnetic Impact

Magnetic field was introduced in laser melting deposition to reduce the pores in workpieces.Finite 3-D model of the coil-deposition layer-substrate was established.Simulation results show that the electromagnetic force in deposition layer mainly concentrates in the projection area of the coil.Axial electromagnetic force shows repulsion in one cycle.The experimental results indicate that the magnetic field is beneficial for grain refinement,microhardness increasement and decline of quantities and average sizes of pores.     

Performance evaluation for MAP state estimate fusion

This paper presents a quantitative performance evaluation method for the maximum a posteriori (MAP) state estimate fusion algorithm. Under ideal conditions where data association is assumed to be perfect, it has been shown that the MAP or best linear unbiased estimate (BLUE) fusion formula provides the best linear minimum mean squared estimate (LMMSE) given local estimates under the linear Gaussian assumption for a static system. However, for a dynamic system where fusion is recursively performed by the fusion center on local estimates generated from local measurements, it is not obvious how the MAP algorithm will perform. In the past, several performance evaluation methods have been proposed for various fusion algorithms, including simple convex combination, cross-covariance combination, information matrix, and MAP fusion. However, not much has been done to quantify the steady state behavior of these fusion methods for a dynamic system. The goal of this work is to present analytical fusion performance results for MAP state estimate fusion without extensive Monte Carlo simulations, using an approach developed for steady state performance evaluation for track fusion. Two different communication strategies are considered: fusion with and without feedback to the sensors. Analytic curves for the steady state performance of the fusion algorithm for various communication patterns are presented under different operating conditions.     

飞机燃油油量测量及姿态误差修正方法

提出了一种基于 CAD技术的航空燃油油量实时测量方法。采用三维实体造型技术 ,建立了某飞机机翼油箱模型 ,利用油量传感器的输出值及飞机姿态信息 ,对燃油油量进行实时测量及姿态误差修正。     

含有任意多个椭圆孔弹性板的应力场计算

本文应用弹性力学的复变函数理论,用多保角变换的方法,导出了含有任意多个椭圆孔的无限大弹性板多复变量应力函数的表达式。每个孔的大小、位置和孔边作用的载荷均为任意指定。板的无限远处作用有和坐标轴方向一致的均匀拉压载荷P_x,P_y和均匀剪切载荷P_(xy)。并在孔边进行复Fourier级数展开,用待定系数法确定应力函数的未知系数,从而计算弹性板的应力场。编制了相应的FORTRAN77标准化程序,进行了考题和算例分析,给出了级数的收敛状况和孔边周向应力的分布图。     

应力为几何更新过程时结构可靠度

本文讨论应力为几何更新过程时结构可靠度，获得在设计基准期［０，Ｔ］内重复应力循环发生的次数服从几何更新过程时结构可靠度表达式。     

气动力星座保持的闭环控制研究

本文研究了利用气动力进行星座保持的闭环控制问题。提出了一种改进的半全局指数收敛闭环控制律，对于指定的任意大的有界域，利用不变集定理论上证明了该控制律的稳定性和抗干扰性，又提出了双ε法以提高响应速度。     

SCP－1型贴片机PLC程序的设计

介绍了在研制ＳＣＰ－１型贴片机过程中，采用可编程控制器（ＰＬＣ）对各外设进行控制的程序编制过程。着重分析了串行口通讯协议的设置，并以吸片过程为例，具体地说明了ＰＬＣ程序的编制方法。     

Implementation of a three-phase high-power-factor rectifier with NPC topology

A three-phase four-wire power factor corrector based on neutral-point-clamped (NPC) topology is adopted to reduce the current harmonics and increase the input power factor. Using the NPC topology, the voltage stress of power switches can be reduced to the half of the dc-link voltage. With the dc-link voltage controller and the phase locked loop circuit, the balanced and sinusoidal line currents can be drawn from the ac supply system under the balance and unbalance mains voltages. The hysteresis current comparators are adopted in the current control loop to track the line current commands. Three voltage levels are generated on the ac terminal to the neutral point. Simulations and experiments are provided to verify the validity and the effectiveness of the proposed control scheme.